ND-110 CPU

From NDWiki
Revision as of 19:54, 30 March 2009 by Gandalf (talk | contribs) (Complete rewrite and added a lot of information. Removing the wikipedia reference.)
Jump to navigation Jump to search

Introduction

The ND-110 is an improvement over the ND-100 in a number of areas.

  • Size. The CPU, the Memory Management System, cache memory and operator panel processor is combined on one single board.
  • New technology. The CPU is constructed by a gate-array. The CPU concists of three VLSI gate arrays, RMIC, RMAC and BUFALU. The ND-110 CPU is also making extensive usage of programmable logic.
  • New cache memory strategy. The first micro instruction word of a macroinstruction is stored in cache memory.
  • Address arithmetic. Address arithmetic is performed in the RMAC gate array, not aby the micro code as in ND-100.
  • The interrupt system. Unlike the ND-100 CPU, the ND-110/CX CPU handles synchronous interrupts as traps, in a similar was as ND-500 does.
  • The Control Store. The control store is based on fast read/write ram instead of prom. At power up the memory is initialised from two 8 kbyte EPROMs. The control store can be read or modified by program.
  • Control logic and timing. Much of the control and timing logic have been moved into PAL chips. The main crystal oscillator is now a 39.3216 MHz oscillator. It is used for the nano-sequencer, the CPU-clock, the bus arbiter, the real time clock and the console UART. The nano-sequencer is a four bit state machine used for timing and control.
  • Power consumption. The power consumption was reduced from 90 watts to 60.[citation needed]

The VLSI chips

  • The Micro Instruction Controller, the MIC - also known as RMIC, for "Rask MIC" ("Speedy MIC"). It replaced three 74S482 sequencers and about 30 other ICs.
  • The Arithmetical and Logical Unit gate array (ALU, also known as the "BUFALU"). Replaced four Am2901 bit-slice processors, and some additional registers like the data bus register the general purpose register, and the internal register block.
  • The Micro Address Controller (The MAC, also called RMAC, for "Rask MAC" ("Speedy MAC"). It implemented hardware address arithmetic, which in the ND-100 had been done in microcode.

Cache memory details

In addition to the macro-instruction cache memory also found in the ND-100, the ND-110 had a unique implementation of cache memory on the micro-instruction level. The step known as mapping in the ND-100 was then avoided because the first micro-instruction word of a macro-instruction was written into the control store cache.

Versions

The ND-110 CPU comes in two versions.

ND-110

This was the standard ND-110 version. In the ND-110 Functional description, appendix E, the ND-110 CPU is described as standard speed.

ND-110/CX

This was the ND-110 with the CX microcode PROM option. The added instructions were the same as the ND-100/CE[citation needed]. In the ND-110 Functional description, appendix E, the ND-110/CX CPU is described as fast speed.

Print versions

  • 3090 An early version of the CPU with two different print release versions (C, K)
  • 3095 A later version of the CPU, only known print release version is B.

New instructions

  • TRA CS - Reads 16 control storage bits into the A-register. The X-register contains the store address.
  • TRR CS - Writes the A-register into 16 control store bits. The X-register contains the control store address.
  • TRR CILP - Cache inhibit individual page.
  • VERSN - Reads version numbers of print and micro program.
  • SETPT - Set page tables.
  • CLEPT - Clear page tables.
  • CLNREENT - Clear non re-entrant pages.
  • CHREENTPAGES - Change page tables.
  • CLEPU - Clear page tables and collect PGU information.
  • WGLOB - Initialize global pointers.
  • RGLOB - Examine global pointers.
  • INSPL - Insert page in page list.
  • REMPL - Remove page from page list.
  • CNREK - Clear non re-entrant pages.
  • CLPT - Clear segment from page tables.
  • ENPT - Enter segment in page tables.
  • REPT - Enter re-entrant segment in page tables.
  • LBIT - Load single bit accumulator (K) with logical memory bit.
  • SBITP - Store single bit accumulator (K) in a physical memory bit.
  • LBYTP - Load the A register with a single byte from physical memory.
  • SBYTP - Store single byte in physical memory.
  • TSETP - Test and set a physical memory word.
  • RDUSP - Read a physical memory word without using cache.
  • LASB - Load the A register with the contents of the segment-table bank (STBNK).
  • SASB - Store the A register contents in the STBNK.
  • LACB - Load the A register with the contents of the core map-table bank (CMBNK).
  • SACB - Store the A register contents in the CMBNK.
  • LXSB - Load the X register with the contents of the STBNK.
  • LXCB - Load the X register with the contents of the CMBNK.
  • SZSB - Store zero in the STBNK.
  • SZCB - Store zero in the CMBNK.

Microcode format

The ND-110/CX microcode format is described in Norsk Data Document ND–06.026 ND-110 Functional Description (ND-06.026.01 rev A page 235).

Reference and Sources