TArntsen: Updated to reflect specification in ND-86128.6 EN (SINTRAN III Commands)

2012-09-25T13:45:30Z

Updated to reflect specification in ND-86128.6 EN (SINTRAN III Commands)

← Older revision		Revision as of 13:45, 25 September 2012
Line 1:		Line 1:
	@COPY-DEVICE <destination device name>, [<unit>,] [<'F' or 'R'>,] <source device name>, [<unit>,] [<'F' or 'R'>]		@COPY-DEVICE <destination device name>, <unit>, [<'F' or 'R'>,] [<subunit>,] <source device name>, <unit>, [<'F' or 'R'>,] [<subunit>]

	Copy all pages from the source (mass storage) device to the destination device.		Copy all pages from the source (mass storage) device to the destination device.
	; <destination device name> : destination - the name of the mass storage device controller on which the device unit is connected. See {{ND-doc\|60.128.01}} Appendix F for legal names.		; <destination device name> : destination - the name of the mass storage device controller on which the device unit is connected. See {{ND-doc\|60.128.01}} Appendix F for legal names.
	; <unit> : the unit number. Only to be specified if [[SINTRAN III]] is generated with multiple units. Unit number starts at 0 (octal~~, default = 0~~).		; <unit> : the unit number. Only to be specified if [[SINTRAN III]] is generated with multiple units. Unit number starts at 0 (octal).
	; <'F' or 'R'> : F = a fixed cartridge disk pack. R = a removable cartridge disk pack. Otherwise, the parameter is not used.		; <'F' or 'R'> : F = a fixed cartridge disk pack. R = a removable cartridge disk pack. Otherwise, the parameter is not used.
			; <subunit> : subunit number. This parameter only applies to disks which are subdivided into several parts or directories (0-7).
	; <source device name> : source - the name of the mass storage device controller on which the device unit is connected. See {{ND-doc\|60.128.01}} Appendix F for legal names.		; <source device name> : source - the name of the mass storage device controller on which the device unit is connected. See {{ND-doc\|60.128.01}} Appendix F for legal names.
	; <unit> : the unit number. Only to be specified if [[SINTRAN III]] is generated with multiple units. Unit number starts at 0 (octal~~, default = 0~~).		; <unit> : the unit number. Only to be specified if [[SINTRAN III]] is generated with multiple units. Unit number starts at 0 (octal).
	; <'F' or 'R'> : F = a fixed cartridge disk pack. R = a removable cartridge disk pack. Otherwise, the parameter is not used.		; <'F' or 'R'> : F = a fixed cartridge disk pack. R = a removable cartridge disk pack. Otherwise, the parameter is not used.
			; <subunit> : subunit number. This parameter only applies to disks which are subdivided into several parts or directories (0-7).

	Rules:		Rules:
Line 14:		Line 16:
	#A directory may exist on the source device.		#A directory may exist on the source device.
	#Destination device must not be entered (@[[ENTER-DIRECTORY]]).		#Destination device must not be entered (@[[ENTER-DIRECTORY]]).
			#Fixed or removable is specified only for 30MB, 60MB, 90MB cartridge disks.
			#Specifying an erroneous disk type as device type the disk will enter fault state and the system will hang.
			#The parameters <unit> are always required.
	#Copying between 10 MB disks takes approximately 4 minutes.		#Copying between 10 MB disks takes approximately 4 minutes.

	Example:		Example:

	@COPY-DEVICE DISC-66MB-2, DISC-66MB-1		@COPY-DEVICE DISC-66MB-2,0 DISC-66MB-1,0

	Copy all pages from one device to the other.		Copy all pages from one device to the other.
Line 24:		Line 29:
	@[[COPY-DIRECTORY]]		@[[COPY-DIRECTORY]]
	== References ==		== References ==
	{{ND-doc\|60.~~128.01~~}} (~~printed June 1980~~)~~, pages 1-4, 1-38, 1-39~~		{{ND-doc\|860128.6}} (October 1988)

	{{ND-doc\|60.174.Q01}}		{{ND-doc\|60.174.Q01}}
	[[Category:System Commands]]		[[Category:System Commands]]

Tingo: created page for the COPY-DEVICE command

2012-09-24T19:12:43Z

created page for the COPY-DEVICE command

New page

@COPY-DEVICE <destination device name>, [<unit>,] [<'F' or 'R'>,] <source device name>, [<unit>,] [<'F' or 'R'>]

Copy all pages from the source (mass storage) device to the destination device.
; <destination device name> : destination - the name of the mass storage device controller on which the device unit is connected. See {{ND-doc|60.128.01}} Appendix F for legal names.
; <unit> : the unit number. Only to be specified if [[SINTRAN III]] is generated with multiple units. Unit number starts at 0 (octal, default = 0).
; <'F' or 'R'> : F = a fixed cartridge disk pack. R = a removable cartridge disk pack. Otherwise, the parameter is not used.
; <source device name> : source - the name of the mass storage device controller on which the device unit is connected. See {{ND-doc|60.128.01}} Appendix F for legal names.
; <unit> : the unit number. Only to be specified if [[SINTRAN III]] is generated with multiple units. Unit number starts at 0 (octal, default = 0).
; <'F' or 'R'> : F = a fixed cartridge disk pack. R = a removable cartridge disk pack. Otherwise, the parameter is not used.

Rules:
#Permitted only for user SYSTEM.
#Valid only for devices which can contain directories
#A directory may exist on the source device.
#Destination device must not be entered (@[[ENTER-DIRECTORY]]).
#Copying between 10 MB disks takes approximately 4 minutes.

Example:

@COPY-DEVICE DISC-66MB-2, DISC-66MB-1

Copy all pages from one device to the other.
== Related commands ==
@[[COPY-DIRECTORY]]
== References ==
{{ND-doc|60.128.01}} (printed June 1980), pages 1-4, 1-38, 1-39

{{ND-doc|60.174.Q01}}
[[Category:System Commands]]

COPY-DEVICE - Revision history

TArntsen: Updated to reflect specification in ND-86128.6 EN (SINTRAN III Commands)

Tingo: created page for the COPY-DEVICE command