Talk:LOAD-MODE:MODE - Revision history

TArntsen: Typo.

2011-12-21T11:10:01Z

Typo.

← Older revision		Revision as of 11:10, 21 December 2011
Line 9:		Line 9:
	APPEND-BATCH 1 LOAD-FILE:SYMB SYS-OUT-1		APPEND-BATCH 1 LOAD-FILE:SYMB SYS-OUT-1
	Does that mean that I could have called the file whatever I wanted? --[[User:Tingo\|Torfinn]] 20:08, 20 December 2011 (CET)		Does that mean that I could have called the file whatever I wanted? --[[User:Tingo\|Torfinn]] 20:08, 20 December 2011 (CET)
	:AFAIK it's just a convention. LOAD-MODE:~~MDOE~~ is common but LOAD-MODE:SYMB was more used in the past. So if your system uses LOAD-FILE:SYMB it's fine, as you see it's in any case defined by you by @NEXT-INITIAL-COMMAND (the first command, set by @INITIAL-COMMAND, must be ENTER-DIRECTORY. Then add the rest with @N-I-C) --[[User:TArntsen\|TArntsen]] 12:07, 21 December 2011 (CET)		:AFAIK it's just a convention. LOAD-MODE:MODE is common but LOAD-MODE:SYMB was more used in the past. So if your system uses LOAD-FILE:SYMB it's fine, as you see it's in any case defined by you by @NEXT-INITIAL-COMMAND (the first command, set by @INITIAL-COMMAND, must be ENTER-DIRECTORY. Then add the rest with @N-I-C) --[[User:TArntsen\|TArntsen]] 12:07, 21 December 2011 (CET)

TArntsen: Minor update

2011-12-21T11:09:10Z

Minor update

← Older revision		Revision as of 11:09, 21 December 2011
Line 9:		Line 9:
	APPEND-BATCH 1 LOAD-FILE:SYMB SYS-OUT-1		APPEND-BATCH 1 LOAD-FILE:SYMB SYS-OUT-1
	Does that mean that I could have called the file whatever I wanted? --[[User:Tingo\|Torfinn]] 20:08, 20 December 2011 (CET)		Does that mean that I could have called the file whatever I wanted? --[[User:Tingo\|Torfinn]] 20:08, 20 December 2011 (CET)
	:AFAIK it's just a convention. LOAD-MODE:MDOE is common but LOAD-MODE:SYMB was more used in the past. So if your system uses LOAD-FILE:SYMB it's fine, as you see it's in any case defined by you by @NEXT-INITIAL-COMMAND (the first command, set by @INITIAL-COMMAND, must be @ENTER-DIRECTORY. Then add the rest with @N-I-C) --[[User:TArntsen\|TArntsen]] 12:07, 21 December 2011 (CET)		:AFAIK it's just a convention. LOAD-MODE:MDOE is common but LOAD-MODE:SYMB was more used in the past. So if your system uses LOAD-FILE:SYMB it's fine, as you see it's in any case defined by you by @NEXT-INITIAL-COMMAND (the first command, set by @INITIAL-COMMAND, must be ENTER-DIRECTORY. Then add the rest with @N-I-C) --[[User:TArntsen\|TArntsen]] 12:07, 21 December 2011 (CET)

TArntsen: Warm start filename convention

2011-12-21T11:07:54Z

Warm start filename convention

← Older revision		Revision as of 11:07, 21 December 2011
Line 9:		Line 9:
	APPEND-BATCH 1 LOAD-FILE:SYMB SYS-OUT-1		APPEND-BATCH 1 LOAD-FILE:SYMB SYS-OUT-1
	Does that mean that I could have called the file whatever I wanted? --[[User:Tingo\|Torfinn]] 20:08, 20 December 2011 (CET)		Does that mean that I could have called the file whatever I wanted? --[[User:Tingo\|Torfinn]] 20:08, 20 December 2011 (CET)
			:AFAIK it's just a convention. LOAD-MODE:MDOE is common but LOAD-MODE:SYMB was more used in the past. So if your system uses LOAD-FILE:SYMB it's fine, as you see it's in any case defined by you by @NEXT-INITIAL-COMMAND (the first command, set by @INITIAL-COMMAND, must be @ENTER-DIRECTORY. Then add the rest with @N-I-C) --[[User:TArntsen\|TArntsen]] 12:07, 21 December 2011 (CET)

Tingo: Is the name a convention?

2011-12-20T19:08:04Z

Is the name a convention?

New page

=Name is a convention?=
Is the name a convention? Instead of a hard rule? I have a machine where the initial commands specify LOAD-FILE:SYMB as the file to run. Like this:
@li-ini-com,,
ENTER-DIRECTORY,,D-74MB-1,0
S-E-D 1
CONNECT SYS-OUT-1 105 R
CLOSE 105
BATCH
APPEND-BATCH 1 LOAD-FILE:SYMB SYS-OUT-1
Does that mean that I could have called the file whatever I wanted? --[[User:Tingo|Torfinn]] 20:08, 20 December 2011 (CET)