ND-100 Status Flags: Difference between revisions

From NDWiki
Jump to navigation Jump to search
m (Clarify ND-500)
(Change header levels for improved readability (easier separation between flag bits and details))
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:
{{stub}}
{{stub}}


The ND-100 status register (STS) bits
The ND-100 '''status register''' ('''''STS''''') bits


=== Page Table Modus ===
== Page Table Modus ==


Bit 0: '''PTM''', Page Table Mode
Bit 0: '''PTM''', Page Table Mode


=== Rounding Indicator ===
== Rounding Indicator ==


Bit 1: '''TG''', rounding indicator for floating point operations
Bit 1: '''TG''', rounding indicator for floating point operations


=== One Bit Accumulator ===
== One Bit Accumulator ==


Bit 2: '''K''', one bit accumulator  
Bit 2: '''K''', one bit accumulator  


=== Error Indicator ===
== Error Indicator ==


Bit 3: '''Z''', error indicator
Bit 3: '''Z''', error indicator


=== Dynamic Overflow Indicator ===
== Dynamic Overflow Indicator ==


Bit 4: '''Q'''', dynamic overflow indicator  
Bit 4: '''Q'''', dynamic overflow indicator  


=== Static overflow Indicator ===
== Static overflow Indicator ==


Bit 5: '''O''', static overflow indicator
Bit 5: '''O''', static overflow indicator


=== Carry Indicator ===
== Carry Indicator ==


Bit 6: '''C''', carry indicator
Bit 6: '''C''', carry indicator
Line 73: Line 73:
The three-way Norsk Data adder can be managed explicity with the RADD instruction, which has modifiers like AD1 (add one), or ADC (add carry), and CM (One's complement). AD1 and ADC cannot be used at the same time, either one of them can set the single bit third operand of the adder.
The three-way Norsk Data adder can be managed explicity with the RADD instruction, which has modifiers like AD1 (add one), or ADC (add carry), and CM (One's complement). AD1 and ADC cannot be used at the same time, either one of them can set the single bit third operand of the adder.


The carry flag as set by ND on subtraction is exactly inverted compared to how the carry flag is set on Intel x86 by its 'sub' instructions. 1-0 sets carry on ND but resets it on x86. The ND-500 carry flag behaves the same way as the Nord-10/ND-100, as can be seen explicitly by its TEST instruction which always set carry.
The carry flag as set by ND on subtraction is exactly inverted compared to how the carry flag is set on Intel x86 by its 'sub' instructions. 1-0 sets carry on ND but resets it on x86. The ND-500 carry flag behaves the same way as the Nord-10/ND-100, as can be seen explicitly by its TEST instruction which always sets carry (the ND-500 TEST instruction is an "N minus 0" operation, i.e. test against zero).


=== Multi-shift Link Indicator ===
== Multi-shift Link Indicator ==


Bit 7: '''M''', multi-shift link indicator
Bit 7: '''M''', multi-shift link indicator


=== Program Level Indicator ===
== Program Level Indicator ==


Bits 8-11: '''PL''', program level indicator
Bits 8-11: '''PL''', program level indicator


=== N-100 ===
== N-100 ==


Bit 12: '''N-100''', ND-100 indicator
Bit 12: '''N-100''', ND-100 indicator


=== Extended Address Mode ===
== Extended Address Mode ==


Bit 13: '''SEXI''', extended address mode indicator
Bit 13: '''SEXI''', extended address mode indicator


=== Memory Management On Indicator ===
== Memory Management On Indicator ==


Bit 14: '''PONI''', memory management on indicator
Bit 14: '''PONI''', memory management on indicator


=== Interrupt System On Indicator ===
== Interrupt System On Indicator ==


Bit 15: '''IONI''', interrupt system on indicator
Bit 15: '''IONI''', interrupt system on indicator

Latest revision as of 08:21, 27 May 2016

The ND-100 status register (STS) bits

Page Table Modus

Bit 0: PTM, Page Table Mode

Rounding Indicator

Bit 1: TG, rounding indicator for floating point operations

One Bit Accumulator

Bit 2: K, one bit accumulator

Error Indicator

Bit 3: Z, error indicator

Dynamic Overflow Indicator

Bit 4: Q', dynamic overflow indicator

Static overflow Indicator

Bit 5: O, static overflow indicator

Carry Indicator

Bit 6: C, carry indicator

The carry indicator is set/reset by add/subtract instructions like ADD, SUB, RADD, RSUB, AAA, AAX, AAT, AAB, but also by RMPY and RDIV. It is both set/reset and used by add with carry, RADD ADC.

How the carry flag is set on addition is well defined, but there are different ways of setting carry on subtraction. Norsk Data uses a method which can most easily be explained as follows: All addition and subtraction is done by a three-way adder, and the carry flag is set if a carry occurs from the sign bit position of the adder.

Example 1:

Addition (using a 4-bit word for simplicity): Add 4 and 1:

 0100
 0001
    0
-----
 0101

Carry not set.

Example 2:

Add 12 and 5:

 1100
 0101
    0
-----
10001

Carry set.

Example 3:

Subtraction: One common method for subtracting binary values is to add the first value to the two's complement of the second value. Norsk Data instead performs subtraction by adding the first value to the one's complement of the second value, plus one:

Subtract 0 from 4:

 0100
 1111
    1
-----
10100

Carry set.

The answer is thus 4, as expected, and carry flag set. This gives a different result than if subtraction had been done via two's complement addition:

 0100
 0000
-----
 0100

Carry not set (this is not the ND method).

The three-way Norsk Data adder can be managed explicity with the RADD instruction, which has modifiers like AD1 (add one), or ADC (add carry), and CM (One's complement). AD1 and ADC cannot be used at the same time, either one of them can set the single bit third operand of the adder.

The carry flag as set by ND on subtraction is exactly inverted compared to how the carry flag is set on Intel x86 by its 'sub' instructions. 1-0 sets carry on ND but resets it on x86. The ND-500 carry flag behaves the same way as the Nord-10/ND-100, as can be seen explicitly by its TEST instruction which always sets carry (the ND-500 TEST instruction is an "N minus 0" operation, i.e. test against zero).

Multi-shift Link Indicator

Bit 7: M, multi-shift link indicator

Program Level Indicator

Bits 8-11: PL, program level indicator

N-100

Bit 12: N-100, ND-100 indicator

Extended Address Mode

Bit 13: SEXI, extended address mode indicator

Memory Management On Indicator

Bit 14: PONI, memory management on indicator

Interrupt System On Indicator

Bit 15: IONI, interrupt system on indicator

References