Search results
Jump to navigation
Jump to search
Page title matches
- @WAIT-FOR-OPERATOR Wait for the operator to restart the user (@RESTART-USER). Rules: #Permitted for all users. #The error device receives the message: ...456 bytes (57 words) - 13:21, 27 September 2017
Page text matches
- Restart the user on a terminal after he has used @WAIT-FOR-OPERATOR. ... @WAIT-FOR-OPERATOR == References == 60.128.03 (printed February 1983 ...521 bytes (55 words) - 11:37, 5 October 2017
- @WAIT-FOR-OPERATOR Wait for the operator to restart the user (@RESTART-USER). Rules: #Permitted for all users. #The error device receives the message: ...456 bytes (57 words) - 13:21, 27 September 2017
- CPU SWAP FILES DISK PASSIVE IO WAIT 00/ 95 00/ 00 ... all for BAK02 file access. BAK02 was in IO-WAIT 60% of the time. The sum of ...2 KB (347 words) - 12:59, 15 August 2017
- ; : (decimal) number of units to wait. ; : can have the values *1 - basic time units (normally 20 milliseconds) *2 - seconds *3 - minutes ...746 bytes (98 words) - 23:48, 8 March 2014
- @WAIT-FOR-OPERATOR == References == 60.128.01 (printed June 1980), page 1-114 60.128.03 (printed February 1983), page 1-145 60.174.Q01 ...666 bytes (81 words) - 11:40, 5 October 2017
- #Current state information (repeat, IO wait, etc). #Ring number. #Priority. #When it was last started or time left until next start. ...949 bytes (123 words) - 21:38, 4 April 2014
- ; : (default = NO) YES = wait for a @START-PRINT after printing . This specification overrides @DEFINE-SPOOLING-CONDITIONS. NO = the text is ...1 KB (182 words) - 12:28, 28 September 2017
- reserved by another user, the calling user must wait until the device is released. #To prevent deadlock, all device numbers must occur in @SCHEDULE ...2 KB (251 words) - 14:07, 14 November 2017
- WAIT 77 % Stop,[1] show 77 in operator panel % No tmp, % Holding space for upper byte of a word % Function to get a 16-bit word from paper ...8 KB (1,241 words) - 19:32, 6 May 2019
- * WAIT – Wait (give up priority) * OPCOM – Operator's Communication Code === Transfer Instructions === ==== Load Independent Instructions ==== ...8 KB (1,031 words) - 13:25, 8 February 2012
- [[Image:ND-100.657 in storage.jpg| 415px | thumb | A long wait in the corner of the storage.]] The power supply has a date of 22/5-81 but the ...3 KB (450 words) - 11:56, 28 September 2016
- adjusted by the RT monitor. Unless in I/O wait the program with the highest priority runs, and the RT monitor lowers the priority of the active ...9 KB (1,163 words) - 10:46, 15 November 2021
- up, but nothing responds. Power off, wait a bit, power on, and the front ... but due to time constraints it will have to wait for a while. ...8 KB (1,319 words) - 07:23, 22 April 2020
- by giving up the priority (by the WAIT instruction, for example). == The Implementation of a Direct Task into a SINTRAN III System == ...4 KB (712 words) - 12:44, 2 October 2017
- | 151000 || WAIT |- | 151400 || NLZ |- | 152000 || DNZ |- | 152402 || SRB |- | 152600 || LRB |- | 153000 || MON |- | 153400 || IRW ...4 KB (413 words) - 21:46, 18 May 2019
- v0.1.5.tar.gz v0.1.5] - Runlevel switching in WAIT, basic rtc interrupt functionality, fixes all over * [http://www.gnyrf.net/nd100em/files/nd100em ...6 KB (927 words) - 14:23, 13 August 2016
- *** In ND-120 a slow microcycle is a minimum (no wait states) of 204.8ns * Bits 37-41 (IDBS - Internal Data Bus Source) ** IDBS 34 - In ND-110 ...6 KB (966 words) - 11:58, 10 February 2024
- 9.1.5.3 Wait or Give Up Priority 9.1.5.4 Monitor Call Instruction 9.1.6 Input/Output Control Instructions 9.1.6.1 IOX - Input/Output ...19 KB (2,088 words) - 00:08, 18 January 2009
- - WRITING TO NONVOLATILE MEMORY, PLEASE WAIT - NEW-PASSWORD (Y/N):N To verify that the CPU model is correct the following command can be used: ...11 KB (1,557 words) - 11:48, 5 November 2023
- 150403) which is the level 16 version of the WAIT instruction. CPU board *processor *memory management *microprogram control *console port ...12 KB (1,813 words) - 02:04, 13 May 2018